Access Control HP400ULACM4 - Honeywell Power Products

Home > Products > Access Control Power Supplies

Access Control Power Supplies

HP400ULACM4

The HP400ULACM4 is a 12VDC power supply that includes a HPACM4 access power controller to be used with card access systems. It provides 12/24VDC through four(4) or independently controlled, power-limited PTC protected outputs. It accept inputs from open collector sink or normally open (NO) dry contacts from UL listed security devices such as keypads, card readers, access control systems, PIR’s and push button delays. Outputs from the HPACM4 can switch power on or off at 12 or 24VDC. Each output can be configured to respond to FACP input. The outputs can also be individually selected as isolated dry contacts (Form “C” configuration). The HPACM4 can be configured for common power, which means the same supply drives both output power and control board power, or alternatively, dual power input, which separates control board power and output power.

Data Sheet - (41 KB PDF)

	UL Listing ALVY.S6677 - Click Here
	UL Listing APHV.S6677 - Click Here
	UL Listing UTRZ.S6677 - Click Here
CSFM LISTING

Specifications
	12VDC operation (0.6A @ 12V, 0.3A @ 24V current consumption with all relays energized).
	Power Supply Input Options: 1. One(1) Common power input (board and lock power). 2. Two(2) isolated power inputs (one[1] for board power, one[1] for lock power).
	Four(4)(HPACM4) access control system trigger inputs (input allows any combination or normally open [NO] inputs or open collector sink inputs).
	Four(4)(HPACM4) independently controlled outputs.
	Output Options: 1. Two(2)(HPACM4) fail-safe and/or fail-secure power outputs. 2. Two(2)(HPACM4) dry Form “C” 5A rated relay outputs. 3. Any combination of the above.
	Four(4)(HPACM4) or eight(8)(HPACM8) auxiliary power outputs (unswitched).
	PTC protected outputs are rated at 2.5A, power limited class 2. NOTE: Output current is determined by the power supply, not to exceed 10A total.
	Red LEDs indicate outputs are triggered (relays energized).
	Fire Alarm Disconnect (latching or non-latching).
	Fire Alarm Disconnect Input Options: 1. Normally open (NO) or normally closed (NC) dry contact input. 2. Polarity reversal from FACP signals circuit.
	Fire Alarm Disconnect Output Options: 1. Four(4)(HPACM4) outputs affected. 2. Two(2)(HPACM4) outputs affected, two(2)(HPACM4) unaffected (50/50 mode).
	FACP output relay (Form “C” contact rated @ 1A, 28VDC not evaluated by UL).
	Green LED indicates when FACP disconnect is triggered.
	Removable terminal blocks facilitate ease of installation.
	Board Dimensions: – HPACM4: 6”L x 4.5”W x 1.25”H (cm: 15L x 11.3W x 3.2H)
	UL Listed for Access Control Systems: UL294
	UL Listed for Fire Alarm Systems: UL1481
	UL Listed for Burglar Alarm Systems: UL603 NOTE: This unit has not been evaluated for elevator equipment and is not authorized for bell output in Mercantile applications.

Power Supply Specifications
	Input Voltage: 120VAC, 60Hz, 2.5A max.
	Output Voltage: 12VDC or 24VDC (jumper selectable).
	4.0A continuous output max., 3.5A plus battery charger.
	Fail safe dry contact output on AC failure (within one minute).
	Built-in charger for sealed lead acid or gel cell type batteries.
	Instantaneous transfer to stand-by battery on AC failure.
	Battery presence detection (within one minute).
	Battery low disconnect at 9.90VDC or 19.9VDC.
	High voltage disconnect at 15VDC or 30 VDC and battery low.
	Fail safe dry contact output for battery trouble (fail safe).
	Battery polarity reversal protection.
	Thermal overload and short circuit protection.
	Yellow LED (L3) indication for battery disconnected.
	DC output PTC activated indicated by red LED (L2).
	DC output failure indicated by red LED (L4).
	AC presence indicated by green LED (L1).
	DC output indicated by red LED (L5).
	Battery leads included.
	Enclosure Dimensions: 13”H x 13.5”W x 3.25”D NOTE: Enclosure accommodates up to two(2) 12AH batteries.