Access Control HP600ULACM8 - Honeywell Power Products

Home > Products > Access Control Power Supplies

Access Control Power Supplies

HP600ULACM8

The HP600ULACM8 is a 12VDC or 24VDC power supply with HPACM4 or HPACM8 access power controllers to be used with Card Access Systems. They provide 12/24VDC through 4 or 8 independently controlled power-limited PTC protected outputs. They accept inputs from open collector sink or Normally Open (NO) dry contacts from UL listed security devices such as keypads, card readers, access control systems, PIR’s and Push Button Delays. Outputs from the HPACM4 and HPACM8 can switch power on or off at 12 or 24VAC/DC. Each output can be configured to respond to FACP input. The outputs can also be individually selected as isolated dry contacts (Form “C” configuration).

The HPACM4 and HPACM8 can be configured for common power, which means the same supply drives both output
power and control board power or alternatively, dual power input, which separates control board and output power. These units have not been evaluated for elevator equipment and are not authorized for bell output in Mercantile applications.

Application Notice - This Application notice gives instruction to qualified personnel on how to configure the HP-UL series power supply to accept an AC line voltage of 230VAC at 50/60Hz. Be sure to measure ac mains output voltage before performing any conversions on power supply.

Data Sheet - (41 KB PDF)

Installation Instructions - (1610 KB PDF)

Drawing - (171 KB PDF)

Enclosure Dimensions - (32 KB PDF)

	UL Listing ALVY.S6677 - Click Here
	UL Listing APHV.S6677 - Click Here
	UL Listing UTRZ.S6677 - Click Here
CSFM LISTING

Specifications - Power Supply Board
	Input voltage: 120VAC 60Hz; Current: 2.50A max.
	Output Voltage: 12VDC or 24VDC, jumper selectable; Current: 6.0A continuous output maximum plus battery charger (DC output not supervised).
	Fail safe dry contact output on AC Failure (within one minute).
	Built-in charger for sealed lead acid or gel cell type batteries.
	Instantaneous transfer to stand-by battery on AC failure.
	Battery presence detection (within 1 minute).
	Battery low disconnect at 9.90VDC or 19.90VDC.
	High voltage disconnect at 15VDC or 30VDC.
	Yellow LED (L3) indication for battery disconnected and battery low.
	Fail safe dry contact output for Battery trouble (Fail Safe).
	Battery polarity reversal protection.
	Thermal overload and short circuit protection.
	DC output PTC activated indication by Red LED (L2).
	DC output failure indication by Red LED ( L4 ).
	AC presence indication by Green LED ( L1 ).
	DC output indication by Red LED ( L5 ).
	Battery Leads included.
	Power Board Dimensions: 6.2”L x 4.7”W x 2.5”H.
	Enclosure Dimension: 17”L x 13.5”W x 4.75”H. Accommodates two 12 Volt 12AH batteries. When using larger batteries, a UL approved enclosure must be used.

Specifications - Access Power Controller Board
	Input – Power supply input 12 or 24 VAC/VDC. – Common Power supply as shipped or dual power supply by cutting links JJ1 and JJ2 – Max. Controller power consumption; • HPACM4 200mA at 12VDC, 187mA at 24VDC. • HPACM8 379mA at 12VDC, 288mA at 24VDC
	Outputs – 4 or 8 independent Fail Safe or Fail Secure Normally Open (NO) or open collector sink (not supervised). – Individually selected outputs for isolated dry contacts by removing J1 through J4, (J8) – Individually selected outputs programmable by dip switch to follow FACP input. – Each PTC protected output rated 2.5A @ 23C with a maximum of 2.0A @ 49C – Automatic Yellow LED status indication of activated PTC. – Test push button lights Yellow LED’s to verify their operation. – Red LED individual indication for each energized relay output
	Fire Alarm Control Panel Input – Polarity reversing input (REV/POL). – Normally open (NO) or normally closed (NC) supervised input with 2.2K Ohm (EOL) resistor. – Engineering Reset (Optional) normally open (NO) or normally closed (NC) input with 2.2 K Ohm (EOL) resistor.
	Alarm Outputs – Alarm outputs are Fail Safe (not supervised). – When FACP activation occurs dry contacts activated. – Green LED indication when FACP is activated. – Dry contacts output for power failure to the HPACM4 or HPACM8.
	Board Dimensions – HPACM4: 5.9” L x 4.5” W x 1.25” H (15 cm L x 11.43 cm W x 3.175 cm H). – HPACM8: 8” L x 4.5” W x x1.25” H (20.32 cm L x 11.43 cm x 3.175 cm H)